DosDevIOCtl

This call performs control functions on a device specified by an opened device handle.

DosDevIOCtl

(Data, ParmList, Function, Category, DevHandle)

Data (PVOID) - input

Address of the data area.
ParmList (PVOID) - input
Address of the command-specific argument list.
Function (USHORT) - input
Device-specific function code.
Category (USHORT) - input
Device category.
DevHandle (HFILE) - input
Device handle returned by DosOpen or a standard (open) device handle.
rc (USHORT) - return
Return code descriptions are:
• NO_ERROR 1
  ERROR_INVALID_FUNCTION
  6
  ERROR_INVALID_HANDLE
  15
  ERROR_INVALID_DRIVE
  31
  ERROR_GEN_FAILURE
  87
  ERROR_INVALID_PARAMETER
  115
  ERROR_PROTECTION_VIOLATION
  117
  ERROR_INVALID_CATEGORY
  119
  ERROR_BAD_DRIVER_LEVEL
  163
  ERROR_UNCERTAIN_MEDIA
  165
  ERROR_MONITORS_NOT_SUPPORTED
  Remarks

  Values returned in the range hex FF00 through FFFF are user dependent error codes. Values returned in the range hex FE00 through FEFF are device driver dependent error codes.

  Refer to the IBM Operating System/2 Version 1.2 I/O Subsystems And Device Support Volume 1 for a complete listing of control functions (DevHlp calls).

  
  Family API Considerations

  Some options operate differently in the DOS mode than in the OS/2 mode. Therefore, the following considerations apply to DosDevIOCtl when coding for the DOS mode.

  The level of support for DosDevIOCtl is identified by category and function code with a noted restriction if it is not supported by DOS 2.X or DOS 3.X Functions tend to be more restrictive in lower version numbers of DOS.

  o

  Category 1 supported as follows:

  • 41H Set Baud Rate
    
  • 42H Set Line Control
    
  • All other category 1 functions are not supported for DOS 2.X and DOS 3.X.
  o
  Category 2 not supported in FAPI
  o
  Category 3 not supported in FAPI
  o
  Category 4 not supported in FAPI
  o
  Category 5 supported in FAPI as follows:

  • 42H Set Frame control - supports IBM Graphics Printers only
    
  • 44H Set Infinite Retry - for DOS 2.X and DOS 3.X, the function is in effect only for the duration of the calling program
    
  • 46H Initialize printer
    
  • 62H Get Frame Control - not supported for DOS 2.X and DOS 3.X
    
  • 64H Get Infinite Retry
    
  • 66H Get Printer Status.
  o
  Category 6 not supported in FAPI
  o
  Category 7 not supported in FAPI
  o
  Category 8 supported in FAPI as follows:

  • 00H Lock Drive - not supported for versions below DOS 3.2
    
  • 01H Unlock Drive - not supported for versions below DOS 3.2
    
  • 02H Redetermine Media - not supported for versions below DOS 3.2
    
  • 03H Set Logical Map - not supported for versions below DOS 3.2
    
  • 20H Block Removable - not supported for versions below DOS 3.2
    
  • 21H Get Logical Map - not supported for versions below DOS 3.2
    
  • 43H Set Device Parameters - not supported for DOS 2.X and DOS 3.X
    
  • 44H Write Track - not supported for DOS 2.X and DOS 3.X
    
  • 45H Format Track - not supported for DOS 2.X and DOS 3.X
    
  • 63H Get Device Parameters - not supported for DOS 2.X and DOS 3.X
    
  • 64H Read Track - not supported for DOS 2.X and DOS 3.X
    
  • 65H Verify Track - not supported for DOS 2.X and DOS 3.X.
  o
  Category 9 is reserved
  o
  Category 10 (0AH) not supported in FAPI
  o
  Category 11 (0BH) not supported in FAPI.

  ---

  [Back: DosDevConfig]
  [Next: DosDevIOCtl2]